11ax 配置 ================================================================================ .. code-block:: ##### IEEE 802.11ax related configuration ##################################### #ieee80211ax: Whether IEEE 802.11ax (HE) is enabled # 0 = disabled (default) # 1 = enabled #ieee80211ax=1 # Require stations to support HE PHY (reject association if they do not) #require_he=1 # disable_11ax: Boolean (0/1) to disable HE for a specific BSS #disable_11ax=0 #he_su_beamformer: HE single user beamformer support # 0 = not supported (default) # 1 = supported #he_su_beamformer=1 #he_su_beamformee: HE single user beamformee support # 0 = not supported (default) # 1 = supported #he_su_beamformee=1 #he_mu_beamformer: HE multiple user beamformer support # 0 = not supported (default) # 1 = supported #he_mu_beamformer=1 # he_bss_color: BSS color (1-63) #he_bss_color=1 # he_bss_color_partial: BSS color AID equation #he_bss_color_partial=0 #he_default_pe_duration: The duration of PE field in an HE PPDU in us # Possible values are 0 us (default), 4 us, 8 us, 12 us, and 16 us #he_default_pe_duration=0 #he_twt_required: Whether TWT is required # 0 = not required (default) # 1 = required #he_twt_required=0 #he_twt_responder: Whether TWT (HE) responder is enabled # 0 = disabled # 1 = enabled if supported by the driver (default) #he_twt_responder=1 #he_rts_threshold: Duration of STA transmission # 0 = not set (default) # unsigned integer = duration in units of 16 us #he_rts_threshold=0 #he_er_su_disable: Disable 242-tone HE ER SU PPDU reception by the AP # 0 = enable reception (default) # 1 = disable reception #he_er_su_disable=0 # HE operating channel information; see matching vht_* parameters for details. # he_oper_centr_freq_seg0_idx field is used to indicate center frequency of 80 # and 160 MHz bandwidth operation. In 80+80 MHz operation, it is the center # frequency of the lower frequency segment. he_oper_centr_freq_seg1_idx field # is used only with 80+80 MHz bandwidth operation and it is used to transmit # the center frequency of the second segment. # On the 6 GHz band the center freq calculation starts from 5.950 GHz offset. # For example idx=3 would result in 5965 MHz center frequency. In addition, # he_oper_chwidth is ignored, and the channel width is derived from the # configured operating class or center frequency indexes (see # IEEE P802.11ax/D6.1 Annex E, Table E-4). #he_oper_chwidth (see vht_oper_chwidth) #he_oper_centr_freq_seg0_idx #he_oper_centr_freq_seg1_idx #he_basic_mcs_nss_set: Basic NSS/MCS set # 16-bit combination of 2-bit values of Max HE-MCS For 1..8 SS; each 2-bit # value having following meaning: # 0 = HE-MCS 0-7, 1 = HE-MCS 0-9, 2 = HE-MCS 0-11, 3 = not supported #he_basic_mcs_nss_set #he_mu_edca_qos_info_param_count #he_mu_edca_qos_info_q_ack #he_mu_edca_qos_info_queue_request=1 #he_mu_edca_qos_info_txop_request #he_mu_edca_ac_be_aifsn=0 #he_mu_edca_ac_be_ecwmin=15 #he_mu_edca_ac_be_ecwmax=15 #he_mu_edca_ac_be_timer=255 #he_mu_edca_ac_bk_aifsn=0 #he_mu_edca_ac_bk_aci=1 #he_mu_edca_ac_bk_ecwmin=15 #he_mu_edca_ac_bk_ecwmax=15 #he_mu_edca_ac_bk_timer=255 #he_mu_edca_ac_vi_ecwmin=15 #he_mu_edca_ac_vi_ecwmax=15 #he_mu_edca_ac_vi_aifsn=0 #he_mu_edca_ac_vi_aci=2 #he_mu_edca_ac_vi_timer=255 #he_mu_edca_ac_vo_aifsn=0 #he_mu_edca_ac_vo_aci=3 #he_mu_edca_ac_vo_ecwmin=15 #he_mu_edca_ac_vo_ecwmax=15 #he_mu_edca_ac_vo_timer=255 # Spatial Reuse Parameter Set # # SR Control field value # B0 = PSR Disallowed # B1 = Non-SRG OBSS PD SR Disallowed # B2 = Non-SRG Offset Present # B3 = SRG Information Present # B4 = HESIGA_Spatial_reuse_value15_allowed #he_spr_sr_control # # Non-SRG OBSS PD Max Offset (included if he_spr_sr_control B2=1) #he_spr_non_srg_obss_pd_max_offset # SRG OBSS PD Min Offset (included if he_spr_sr_control B3=1) #he_spr_srg_obss_pd_min_offset # # SRG OBSS PD Max Offset (included if he_spr_sr_control B3=1) #he_spr_srg_obss_pd_max_offset # # SPR SRG BSS Color (included if he_spr_sr_control B3=1) # This config represents SRG BSS Color Bitmap field of Spatial Reuse Parameter # Set element that indicates the BSS color values used by members of the # SRG of which the transmitting STA is a member. The value is in range of 0-63. #he_spr_srg_bss_colors=1 2 10 63 # # SPR SRG Partial BSSID (included if he_spr_sr_control B3=1) # This config represents SRG Partial BSSID Bitmap field of Spatial Reuse # Parameter Set element that indicates the Partial BSSID values used by members # of the SRG of which the transmitting STA is a member. The value range # corresponds to one of the 64 possible values of BSSID[39:44], where the lowest # numbered bit corresponds to Partial BSSID value 0 and the highest numbered bit # corresponds to Partial BSSID value 63. #he_spr_srg_partial_bssid=0 1 3 63 # #he_6ghz_max_mpdu: Maximum MPDU Length of HE 6 GHz band capabilities. # Indicates maximum MPDU length # 0 = 3895 octets # 1 = 7991 octets # 2 = 11454 octets (default) #he_6ghz_max_mpdu=2 # #he_6ghz_max_ampdu_len_exp: Maximum A-MPDU Length Exponent of HE 6 GHz band # capabilities. Indicates the maximum length of A-MPDU pre-EOF padding that # the STA can receive. This field is an integer in the range of 0 to 7. # The length defined by this field is equal to # 2 pow(13 + Maximum A-MPDU Length Exponent) -1 octets # 0 = AMPDU length of 8k # 1 = AMPDU length of 16k # 2 = AMPDU length of 32k # 3 = AMPDU length of 65k # 4 = AMPDU length of 131k # 5 = AMPDU length of 262k # 6 = AMPDU length of 524k # 7 = AMPDU length of 1048k (default) #he_6ghz_max_ampdu_len_exp=7 # #he_6ghz_rx_ant_pat: Rx Antenna Pattern Consistency of HE 6 GHz capability. # Indicates the possibility of Rx antenna pattern change # 0 = Rx antenna pattern might change during the lifetime of an association # 1 = Rx antenna pattern does not change during the lifetime of an association # (default) #he_6ghz_rx_ant_pat=1 # #he_6ghz_tx_ant_pat: Tx Antenna Pattern Consistency of HE 6 GHz capability. # Indicates the possibility of Tx antenna pattern change # 0 = Tx antenna pattern might change during the lifetime of an association # 1 = Tx antenna pattern does not change during the lifetime of an association # (default) #he_6ghz_tx_ant_pat=1 # 6 GHz Access Point type # This config is to set the 6 GHz Access Point type. Possible options are: # 0 = Indoor AP # 1 = Standard power AP # 2 = Very low power AP (default) # 3 = Indoor enabled AP # 4 = Indoor standard power AP # This has no impact for operation on other bands. # See IEEE P802.11-REVme/D4.0, Table E-12 (Regulatory Info subfield encoding) # for more details. #he_6ghz_reg_pwr_type=0 # # 6 GHz Maximum Tx Power used in Transmit Power Envelope elements, where the # "Transmit Power Interpretation" is set to "Regulatory client EIRP PSD". # For Maximum Transmit Power Category subfield encoding set to default (0): #reg_def_cli_eirp_psd=-1 # For Maximum Transmit Power Category subfield encoding set to subordinate (1): #reg_sub_cli_eirp_psd=-1 # Unsolicited broadcast Probe Response transmission settings # This is for the 6 GHz band only. If the interval is set to a non-zero value, # the AP schedules unsolicited broadcast Probe Response frames to be # transmitted for in-band discovery. Refer to # IEEE P802.11ax/D8.0 26.17.2.3.2, AP behavior for fast passive scanning. # Valid range: 0..20 TUs; default is 0 (disabled) #unsol_bcast_probe_resp_interval=0